Furman PL-PRO C 20-amp power line conditioner and surge protector with voltmeter

Features

Overview: The Furman Classic Series PL-Pro C is rack-mountable power conditioner, designed for use by audio/video professionals, contractors, broadcasters, and musicians. It has 8 high-quality AC outlets on the rear panel, plus a front panel convenience outlet, all controlled by a single switch. It features a multi-segment LED voltmeter on the front panel so you can confirm at a glance you're running at optimal voltage levels. The unit is equipped with rack ears, and takes up 1U of rack space. The PL-Pro C has a flexible, 10' power cord with three 12-gauge conductors and a NEMA 20 plug (requires a special 20-amp receptacle with perpendicular blades).

Applications: The PL-Pro C is recommended for professional audio and video applications, and can be installed in permanent or portable rack systems. They can be used to protect your mixing boards, amps, preamps, and effects generators from power spikes and surges when you go on the road. In the recording studio, the RFI/EMI filtering can give you cleaner recordings by removing noise cause by dirty AC power. In addition, the front panel lights can also help you see the controls on your equipment when you're working in a darkened night club, bar, or other venue.

AC Outlets: The PL-Pro C has eight 3-pronged outlets on the rear panel, divided into two isolated banks to minimize inter-component interference and noise contamination. The three outlets in Bank 1 are widely spaced to accommodate bulky AC power transformers ("wall warts"). Bank 2 has five outlets spaced narrowly apart to accommodate standard-sized AC plugs. There is a single 3-pronged outlet on the front panel, providing a convenient place to temporarily plug in a device, when needed.

USB Charging Port: For convenience, a Type-A USB charging port is provided on the front panel for powering or charging a smartphone, tablet, MP3 player, or other device that charges via USB.

SMP (Series Multi-stage Protection): Furman's exclusive SMP technology provides the highest level of surge and spike protection available.

EVS (Extreme Voltage Shutdown): The PL-ProC will shut itself off when it detects dangerous voltage irregularities, protecting the connected equipment from unsafe conditions.

LiFT (Linear Filtering Technology): The PL-Pro C filters the incoming AC power to insure your equipment is receiving clean power for optimum audio and video performance.

LED Indicators: Two front panel status LEDs indicate when the surge protection and noise filtering are working (Protection OK), and can alert you when the voltage is outside of the normal range (Extreme Voltage).

LED Voltmeter: The PL-Pro C has a three-color, multi-segment LED AC voltage meter that displays the incoming voltage in 2-volt steps from 90 to 128 volts. This bar-graph volt meter indicates optimal voltage in green LEDs, with moderate and extremely high or low voltages in yellow and red, respectively. In addition, abnormal conditions are indicated by special flashing patterns: the single left-most LED flashing indicates marginally low voltage; all LEDs flashing indicates marginally high voltage; and no LEDs lit except the Extreme Voltage LED indicates the unit's has shut down power because the voltage has exceeded 140 volts.

Pull-out Lights: The PL-Pro C features two "smooth track" retractable LED lights that illuminate the front panels of the equipment in the rack. The round "tubes" pull out 3", rotate approximately 90 degrees, and contain three LEDs each (one white and two amber). The lights can be turned on/off or dimmed with the front panel switch.

BNC Lamp Connector: In addition to the front panel lights, a BNC connector is provided for powering a standard gooseneck lamp (not included) for rear rack illumination. It is rated for 12VAC 500mA.

Specifications:

• Maximum Output Current: 20 Amps
• Operating Voltage: 90 to 139 VAC
• Over Voltage Shutdown: 140 VAC
• Spike Protection Mode: Line to neutral, zero ground leakage
• Spike Clamping Voltage: 188 VAC peak @ 3000 Amps, 133 VAC RMS
• Response Time: 1 nanosecond
• Maximum Surge Current: 6500 Amps
• Noise Attenuation: 10dB @ 10 kHz, 40dB @ 100 kHz, 50dB @ 500 kHz
• Dimensions: 19" W x 10.5" D x 1.75" H
• Weight: 12 pounds
• Power Consumption: 15 VA

Furman Warranty Information

Shipping Policy at CapitalSound.ca

Free Shipping Across Canada

At CapitalSound.ca, we are pleased to offerFree Standard Shipping on all orders within Canada. No minimum purchase required. Experience the top-notch quality of our products without the additional cost of shipping.

Estimated Delivery Time

• Orders are typically processed within 1-2 business days.
• Standard shipping generally takes 3-7 business days.

What to Expect

1. Order Confirmation: You will receive an order confirmation email as soon as you have placed an order. Please keep this email for your records.
2. Shipment Notification: We will send you a shipment notification email when your order has been shipped.

Additional Information

• Signature may be required upon delivery.
• We currently do not ship to P.O. Boxes.

Shipping Damage Policy

If the shipping box shows signs of physical damage, we recommend inspecting the product while the shipping company is present. Minor punctures or dents to the box do not often result in damage to the well-padded product inside, so a refusal of delivery is generally not necessary for minor box imperfections. However, should the product itself show signs of damage, it must be refused at the time of delivery for an RMA. Products not refused due to damage at the time of delivery will not be eligible for RMAs. To ensure your full rights to warranty and potential future claims, please have the delivery company note any box damage on file, even if the product itself appears undamaged.

Questions?

For any questions regarding your order, please contact us.